[im]Duino - MCU development board based on Arduino - FAQs and Tutorial

[beginner wan]

[im]Duino is a microcontroller development board based on Arduino (Arduino software compatible). This development kit from [im]aginatech Inc. is an electronics prototyping platform based on flexible, easy-to-use hardware and software. Students, hobbyists and anyone (from beginner to advance programmers) interested in making their own projects will find an easier time in doing their interactive objects and environments.






SPECIFICATIONS:

   * Atmega8 Chip
   * 8KB Flash program memory
   * 1KB RAM
   * 16 MHz Oscillator frequency
   * 14 Digital I/O Pins
   * 6 Analog input pins (can be also used as digital pins)
   * 3 pins for PWM output
   * UART 4-pin male header
   * Pin4 (SDA) and pin5 (SCL) can be used for I2C (two-wire serial bus)
   * Pin10 (SS), pin11 (MOSI), pin12 (MISO) and pin13 (SCK) can be used for SPI (Serial Peripheral Interface).
   * The onboard full bridge rectifier permits either DC (either polarity) or AC supply with voltages ranging
       from 9v to 20v.
   * A built-in LED connected to digital pin13 is useful for testing sketches.
   * LEDs dedicated for Tx and Rx.
   * Dimensions: 1.875” x 3.45”

Package includes [im]Duino board, serial cable and a CD for the software and included tutorials.

price: 800 pesos

for orders please visit: www.imaginatechinc.com or PM me.. 

[ajak]

ayus, tutorial na..

[[J]sil]

Hay salamat up na ulit ang boards... at marami akong itatanong bwahahaha

Compatible ba ang [im]duino sa RS232->USB?
Patingin po ulit nung code na nag si-simulate ng PWM (may tumangay ng thumbdrive ko buti hindi pinagdiskitahan yung prototype haha)

BTW.
Interesado ang ibang mga kaklase (at prof na kaklase ng fren kong MS) ko sa [im]duino na relay ko na details sa kanila 

[beginner wan]

waw! salamat sir [j]sil!

bout po sa first question, yes sir, pwedeng pwede po sya gamitan ng USB to serial.. tried and tested many times!

eto po yung sample code for PWM..

Fading LED using PWM

Pulse Width Modulation or simply PWM is a technique where we can create a “fake” analog output in a digital system by
pulsing its output. In the next sample sketch, we will be using PWM in order to dim or brighten an LED.

Code:

int ledPin = 9;                           // PWM pin for the LED
int val = 0;                              // set val equal to zero

void setup()
{}                                          // no setup needed


void loop()
{
    for (val=0; val<=255; val++)               // ascending value for val
    {
       analogWrite(ledPin, val);                 // sets brightness level to val
       delay(50);                                    // pauses for 50ms
    }

    for (val=255; val>=0; val--)                // descending value for val
    {
       analogWrite(ledPin, val);                   // sets brightness level to val
       delay(50);                                      // pauses for 50ms
    }
}

[beginner wan]

clearer view of [im]Duino board..

[[J]sil]

Oo nga pala, [im]duino ko nilagyan ko ng bump-on rubber stickers (from 3M) para hindi madikit at mag short yung mga metal parts sa ilalim. tapos sa varnished wood table kasi ako nagttrabaho matagal ko nang napansin pero hindi ko lang na post pero once na naipatong sa table yung kamay ko kahit hindi ko hawak yung [im]duino umiilaw ung D11 pag bitaw nag o-off din parang switch tuloy yung table top ano kayang nangyayari

[beginner wan]

sa wood na table din ako gumagawa lalu sa bahay.. yung umiilaw na LED paghinawakan, nangyayari din sakin yun.. i dont know whats the exact explanation about that..   

[rdpzycho]

baka malakas kayong mag-create ng static. hehehe.

[danny]

just a suggestion, if you can afford
to buy antistatic mat and wrist starp mas ok un
ugaliin natin sana yung gumamit nun
para mas safe ang mga electronics component natin
 

[rdpzycho]

meron ding mga tao na malakas talaga mag-store ng static. kapag dumidikit ako sa GF (dati pati sa best friend ko) ko habang naglalakad nagagalit siya kasi ang lakas niya makuryente. hehehe.

kailan lang ako nagkaganun, simula lang nung nahilig ako sa ESD testing. kaya ngayon nagdi-discharge na ako ng PC casing kapag may inaayos.

[danny]

sir rd baka kakaibang kuryente na ang gumagapang nyahahah.
 

[rdpzycho]

 

[danny]

out of topic na
baka yariin na tau ni sister wan
muhahaa
sori po 

[rdpzycho]

 

[[J]sil]

Naka antistatic wrist strap ako that time.

Busy yung friend kong kabibili kang kahapon ng [im]duino hehe

[beginner wan]

Naka antistatic wrist strap ako that time.

Busy yung friend kong kabibili kang kahapon ng [im]duino hehe

hehehe.. busy ba si sir jay? pag may prob sya sir, paki text nalang ako or post nyo dito..

[Tambay_7]

real-time online support

[beginner wan]

empre, pag pwede magsumagot, sasagot.. pero pag hinde, antay ng free time.. hehehe..

[Tambay_7]

that's great

[Pupil]

uy! ok to ah.. ngayon ko lang nakita to.. wala pang testimonials kung gaano sya kahirap gamitin?